Topseller
MCS, Hollow axle plug tool
MCS-987924 - Includes 2 plugs. Plugs into left & right side of axle and are used to find the correct center point; for correct wheel alignment; on late H-D models with hollow axles. Just lube the O-rings and insert into the rear axle for...
Inhalt
1 Stück
57,73 €
*
JIMS, wheel bearing support plate
MCS-978641 - Optional support plate for wheels with outboard mounts. Used with JIMS 978386 wheel bearing tool to prevent damage to some Cast/CVO and/or accessory wheels with outboard mounts. Note: For use with JIMS 978386 tool. Fitment:...
Inhalt
1 Stück
170,95 €
*
JIMS, 00-up sealed wheel bearing tool
MCS-978386 - Remove & install all 3/4" (19.05mm); 1" (25.4mm) and 25mm ID wheel bearings; Note: Use 978641 optional support plate for 14-up Touring some cast wheels with outboard mounts Fitment: 00-22 B.T.; 00-22 XL; 02-17(NU)V-Rod. (ABS...
Inhalt
1 Stück
609,01 €
*
JIMS, wheel bearing lock nut socket
MCS-978379 - Used to remove & install the slotted lock nut; on wire wheels (spoked wheels) with drum brakes; to correct torque Fitment: 67-72 B.T.; XL (NU)
Inhalt
1 Stück
151,87 €
*
JIMS, WHEEL/SWINGARM BEARING RACE TOOL
MCS-978238 - Used to remove & install wheel bearing and swingarm bearing races Note: Used with 920542 JIMS driver handle Fitment: WHEEL: 73-99 B.T.; XL BUELL; SWINGARM 58-86 4-SP B.T.(NU)
Inhalt
1 Stück
195,54 €
*
George''s Garage, 00-up sealed wheel bearing tool
MCS-979464 - Removes & installs all 1 inch and 25mm sealed wheel bearings Fitment: 00-22 B.T.; 00-22 XL; 02-17(NU)V-Rod. (ABS or non-ABS)
Inhalt
1 Stück
404,50 €
*
George''s Garage, driver handle 12"
MCS-979461 - Used with 979457 steering head bearing race tool and 979453 wheel bearing race tool
Inhalt
1 Stück
82,51 €
*
George''s Garage, wheel bearing race tool
MCS-979453 - 2-piece design. Used to remove and install wheel bearing race of Timken bearings for use with 3/4" diameter axle. Also used for swingarm Timken bearings of 58-86 4-speed Big Twin models. Note: requires use of 979461 driver...
Inhalt
1 Stück
97,23 €
*
JIMS, rear wheel compensator bearing tool
MCS-961446 - Used to remove and install the special compensator 25mm ball bearing (OEM 9276A) as used on models equipped with a rear pulley with rubber dampers. Note: The pictured press is not included and not available. Fitment: 08-22...
Inhalt
1 Stück
498,76 €
*
JIMS, FLT/Touring rear wheel axle tool
MCS-961553 - Loosen and tighten the 36mm OEM 8020 36mm (M24 x 2.0 x 15) rear wheel axle nut; for drive belt tension or alignment adjustment; without removing the muffler. The built-in square allows use with a 1/2" drive wrench to apply...
Inhalt
1 Stück
74,76 €
*
JIMS, wheel rotator tool
MCS-961453 - Placed under the wheel; Used to rotate the wheel with a wrench; Perfect for making timing adjustments to the engine Fitment: UNIV.
Inhalt
1 Stück
405,71 €
*
JIMS, wheel alignment tool
MCS-961441 - Tool clamps to the chain and the indicator rod gives a clear indication if the rear wheel is correctly aligned. If not adjust the rear wheel until indicator rod runs in line with the chain towards the front sprocket....
Inhalt
1 Stück
73,05 €
*