Topseller
JIMS, 70-99 cam relief tool
MCS-978473 - Used to remove material from crankcase to install larger than stock cam. Can be driven by a standard motor drill with a 1/2" chuck. Fitment: 70-99 B.T. (excl. Twin Cam)
Inhalt
1 Stück
455,64 €
*
JIMS, TC cam relief tool. Dual spindles
MCS-978472 - Dual spindle; Used to machine cases for high lift cams Fitment: 99-06 Twin Cam (excl. 2006 Dyna) (NU)
Inhalt
1 Stück
924,42 €
*
JIMS, TC cam relief tool. Single spindle
MCS-978471 - Single spindle; Used to machine cases for high lift cams; Note: This tool has one spindle cutter and must be re-mounted to clear the opposite cam side; Note: See 978472 for dual spindle cam relief tool Fitment: 99-06 Twin...
Inhalt
1 Stück
666,48 €
*
JIMS, Sportster pinion gear locker tool
MCS-978468 - Used to lock pinion gear; when torquing down or removing the pinion nut. Use with socket wrench or hand wrench. Do not use an impact wrench. Fitment: 00-22 XL; 00-10(NU)Buell (excl. 1125 models)
Inhalt
1 Stück
82,48 €
*
JIMS, Sportster pinion gear locker tool
MCS-978467 - Used to lock pinion gear; when torquing down or removing the pinion nut. Use with socket wrench or hand wrench. Do not use an impact wrench. Fitment: 91-99 XL; Buell (NU)
Inhalt
1 Stück
82,48 €
*
JIMS, compression release thread tap tool
MCS-978425 - 10x1.0 tap. Used to tap threads for JIMS 978426 compression release valve set. Note: 978424 compression release valve tool can be used to aid tapping threads correctly in 99-17 Twin Cam heads. Fitment: 99-17 Twin Cam (may...
Inhalt
1 Stück
92,89 €
*
JIMS, wrist pin clip tool
MCS-978422 - Used to easily remove and install the wire type wristpin clips without hassle; over-squeezing clip or damage to piston. Note: Not for use with forged pistons. Fitment: 84-99 Evo B.T.(NU)
Inhalt
1 Stück
479,48 €
*
JIMS, balancer bearing tool
MCS-978417 - Used to pull the engine balancer bearings from the case in one easy smooth motion; thus preventing any damage to the bearing bores. Installation is done with the install portion of this tool by pushing on the outer diameter...
Inhalt
1 Stück
227,74 €
*
JIMS, balancer shaft alignment tool
MCS-978416 - A must for maintaining a long life of balancer drive chains and bearings. Takes the guess-work out of setting up the sprocket & chain assembly on Twin Cam Softail models. This tool must be treated with great care; as you...
Inhalt
1 Stück
440,33 €
*
JIMS, REPL. 1 3/4 INCH LAP HEAD
MCS-978412 - USE WITH 978411 CRANKCASE LAP TOOL
Inhalt
1 Stück
499,95 €
*
JIMS, crankcase lap tool
MCS-978411 - Used to lap pinion bearing race in the right crankcase. Removes more material in less time but with greater accuracy than a conventional lap. The JIMS case lap is guided on both sides of the pinion bearing race. This...
Inhalt
1 Stück
1.489,87 €
*
JIMS, replacement 1 1/2" OD lap head
MCS-978409 - Replacement for 978407 JIMS connecting rod lap set
Inhalt
1 Stück
215,25 €
*